+34 688 945 030
Catalyst suppression / replacement system. (Requires about 2 hours of assembly) It grants greater sonority and optimizes the power of the motor. Valid for 900 and 1200 engines. Fits on the following models: 100 LC, T120, Street Twin, Street Cup, Thruxton R, Thruxton S, Bobber, Speedmaster, Spedd Twin* Not suitable for Scrambler models due to the...
Desde 14,63 € al mes
Catalyst suppression / replacement system. (Requires about 2 hours of assembly) It grants greater sonority and optimizes the power of the motor. Valid for 900 and 1200 engines. Fits on the following models: 100 LC, T120, Street Twin, Street Cup, Thruxton R, Thruxton S, Bobber, Speedmaster, Spedd Twin * Not suitable for Scrambler models due to the superior...
Supplied with cap in BRUSHED ALUMINUM finish Kit suitable for: Triumph Twins 2001-2015 (T100, Thruxton, SE, Scrambler) Triumph Twins since 2016 (Bobber, T100, T120, Street Cup, Street Twin, etc.)Harley Davidson since 1983 (Sportster, Dyna, etc.)Monza plug made by Motone with modern DIE CAST HIGH PRESSURE technology in high quality aluminum
Desde 10,38 € al mes
The seat base is adapted for the entire Triumph air-cooled range from 2001 to 2015. 25.4mm thinner than the serial width. Built on an ABS injection molded base. Use of polyurethane foam of 80 kg / m3 high density for high comfort ADEQUATE LENGTH FOR PILOT AND PASSENGER UPHOLSTERY ROMBOIDAL
Desde 29,54 € al mes
The seat base is adapted for the entire Triumph air-cooled range from 2001 to 2015. 25.4mm thinner than the serial width. Built on an ABS injection molded base. Use of polyurethane foam of 80 kg / m3 high density for high comfort ADEQUATE LENGTH FOR PILOT AND OCCASIONAL PASSENGER UPHOLSTERY ROMBOIDAL
Desde 29,54 € al mes
Supplied with cap in BRUSHED ALUMINUM finish Kit suitable for: Triumph Twins 2001-2015 (T100, Thruxton, SE, Scrambler) Triumph Twins since 2016 (Bobber, T100, T120, Street Cup, Street Twin, etc.)Harley Davidson since 1983 (Sportster, Dyna, etc.)Monza plug made by Motone with modern DIE CAST HIGH PRESSURE technology in high quality aluminum
For those wanting to use the part for a custom application (non-triumph) the distance between the 2 slotted horizontal bolt holes centre to centre is 85mm (3.34 inches
Custom lathed out of Aluminum. Sides of the top cap knurled for extra grip the lower threaded part of the cap has a spring-bound valve system centrally located in the middle of the bung. This connects to 3 vents in the top part of the cap to allow alleviation of any pressure that may build up inside the tank. It also comes with a petrol-resistant o-ring...
Desde 7,58 € al mes
A complete set of side Engine Covers designed to replace the original equipment item. Finished in high quality chrome This item fits Bonneville T120, Bonneville T120 Black, Street Twin, Thruxton 1200, and Thruxton R 1200 models. * NOTICE: SINGLE PIECE FROM EXPOSURE. FOR SALE AS IS SEEN IN THE PHOTOS.
Desde 25,83 € al mes
CAN BUS adapter to mount MOOTGADGET speedometers on Triumph EFIs with control unit Uses the original connector, connecting the assembly to the color-coded mo.tri terminals No welding or wire detection Does not void the vehicle warranty Near Plug 'n' Ride installation
Pair of Triumph tank pads (or any bike it fits) Manufactured from a high quality and resistant composite vulcanized natural rubber Design: Union Jack Black Adhesive: 468MP Automotive 3M - selected for its strength and resistance to all weather elements plus gasoline.
Desde 6,71 € al mes
Motone custom ribbed side panel Made of high quality precision injection molded ABS. LEFT SIDE ONLY Ideal for Triumph Scramblers or for models with top mount tubes Ribs aligned with the angle of the cylinder fins Windows lined with aluminum mesh. Panels come with rubber grommets
Desde 10,88 € al mes
Electronic speed converter for KOSO speedometers Converts the mechanical signal to electronic. Includes 3-wire connector with faston connector cable length: approx 1,2 meter Compatible motorcycle models listed below
The seat base is adapted for the entire Triumph air-cooled range from 2001 to 2015. 25.4mm thinner than the serial width. Built on an ABS injection molded base. Use of polyurethane foam of 80 kg / m3 high density for high comfort ADEQUATE LENGTH FOR PILOT AND PASSENGER UPHOLSTERY ROMBOIDAL
Desde 29,54 € al mes
The SKINNY seat base is designed for a snug fit on the original frame rails.Made from an injection molded ABS base to fit the entire air-cooled Triumph range from 2001 to 2015. SUITABLE LENGTH FOR PILOT AND PASSENGER LINEAR HORIZONTAL PATTERN
Desde 29,54 € al mes
Chrome-plated closing cap with key to prevent theft or illegal manipulation of fuelClosing with a sliding cover that protects the lock from dirt and impuritiesIncludes two keyse thread.
Manufactured by MotoneIn satin black painted aluminum The same screws are used as the standard motorcycle Plug & Play Valid for: 2009-2015 (Air Cooled) Bonneville Mag Wheel Only
Manufactured by Motone Black anodized aluminum Pre-drilled and ready to mount any of the Motone Fender Mount Light Kits (Eldorado, Bel Air, Lecter, Cuda, Big Fin, etc.) With hole for wiring (recommended TE014) Measurements: 570 mm long and 180 mm wide
Slim-cut low-profile seat with a minimalist look taking advantage of the original frame measurement while maintaining optimal comfort Injection molded ABS base High density, high comfort injection molded polyurethane foam For models: Street Twin / Street Cup / Street Scrambler / T100 / T120 RIGHT LENGTH FOR RIDER AND PASSENGER LINEAR HORIZONTAL PATTERN